Extron-electronics AVTrac (482) User Guide Manual de usuario

68-1803-01 Rev. B12 10Floor-mount Raceway with Modular AAPConnectivity for A/V, Data, and PowerAVTrac®User GuideArchitectural Connectivity

Before Getting StartedPlanningAVTrac can be installed before new carpeting is fitted or retrofitted under preexisting carpet. It can also be installed i

Room ConsiderationsDetermine the A/V requirements for the room. Extron provides a complete range of AAPs that can be purchased separately to provide f

Tools and Equipment Required Before InstallationAlmost everything you need to install your AVTrac system has been included. You will need some basic t

InstallationStep 1: TrackBy this point you must have decided exactly where the AVTrac will be installed, checked the contents of the kit, and gathered

Prelaid Carpet Rolls — Cut CarpetWhen the positioning of preinstalled furniture makes it impossible to remove existing carpet, the carpet must be cut

3. Using a drill and box cutters or a saw, cut a hole at the base of the wall 4 inches wide by 1½ inches high (10.1 cm x 3.8 cm).If there is a metal

5. Drill mounting holes in the shallow grooves of the base track and side ramps using a 1/4 inch bit for drilling metal (not supplied).NOTE: Mountin

7. Lay the base track on the floor in the prepared location.Mate the tabs in the side ramps with the grooves in the base track, and place the end ramp

Step 2: Connectivity BoxBy this point, the base track, side ramps and end ramps must be securely fastened to the floor.To attach the connectivity box t

Step 3: AC Power ModuleBy this point, the base of the connectivity box must be securely fastened to the floor.If your AVTrac system does not include th

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipmen

Step 4: Architectural Adapter Plates (AAPs)At this point, the track, ramps and connectivitly box must all be securely in place. If an AC power module

Step 5: Completing the InstallationAt this point, the track and connectivity box must be secured to the floor, the electrical power must be connected,

4. Glue or tape the carpet to the floor and side ramps.NOTE: Do not use the supplied tape to attach the carpet to the ramp. The tape is intended only

The figure below shows a completed AVTrac installation, which safely and discretely runs power, data, and A/V cables from a wall to a table, podium, or

Specications GeneralPower ... 125 VAC, 50-60 Hz, 20 A (max.)Mounting optionsTrack system (track and ramps)

Connectivity box ... 3.55" H x 4.27" W x 12.0" L (9.0 cm H x 10.8 cm W x 30.5 cm L) SIDE VIEWTOP VIEWEND VIEWProdu

Reference InformationOptional AccessoriesAVTrac AccessoriesAccessory Part NumberAVTrac 4 feet Track Extension Kit70-645-04Connectivity Box (AAP Enclos

Extron® WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of pur

Installation ChecklistInstallation of the AVTrac can be divided into six main sections:Before Getting Started  Open the three boxes containing the AV

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

ContentsIntroduction ... 1Overview ... 1AVTrac Floor Sys

AVTrac • Contents vi

IntroductionOverviewThis guide describes the AVTrac® components and provides instructions for installation.MLS 406MAMediaLink SwitcherCONTROLPEAKCLIPS

Kit ContentsBox 1The AVTrac Kit is shipped in three boxes.• Box 1 contains the connectivity, conduit and accessory components. • Boxes 2 and 3 conta

Boxes 2 and 3Check the contents of each box to ensure all items are present.Plastic Te mplate (1)Side Ramp (2)AluminumCover Tr ack (1)AluminumBase Tr