Extron-electronics FOX T UWP 302 User Guide Manual de usuario

User GuideFOX T UWP 302Fiber Optic ExtenderTwo Input Fiber Optic Transmitter68-2092-01 Rev. A 07 13

Installation and OperationThis section describes procedures to cable, connect, and manually operate the FOX T UWP 302. Topics in this section include

Rear Panel FeaturesTxRxRxTx12G+REMOTERS-232ALARMPOWER12V0.6A MAX-RearRight SideabcFigure 2. FOX T UWP 302 Rear Connectors from the Side and Rear Pane

Front Panel FeaturesOutside-the-Faceplate FeaturesPOWERPCHDMIHDCPAUDIO INPUTHDMI INPUTCOMPUTER INPUTAUDIObdcaFigure 3. FOX T UWP 302 Outside-the-Face

Under-the-Faceplate FeaturesLINK 1LINK 2HDMI INPUTAUDIO INPUTCOMPUTER INPUTPOWERRESETCONFIGPCHDMIHDCPAUDIOfegFigure 5. FOX T UWP 302 Under-the-Facepl

Mounting and Making ConnectionsMountingBefore mounting an electrical UL Listed junction box, consider the mounting location and prepare the surface as

Connecting the HDMI ConnectorUse an Extron LockIt Lacing Bracket to secure an HDMI cable to each device as follows:3abcdeFigure 7. Installing the Loc

Wiring for Remote RS-232 and Alarm CommunicationThe Remote RS-232 and Alarm connector is for RS-232 control (such as updating firmware, status queries

Wiring the Power SupplyConnect 12 VDC power supply to the 3.5 mm, 2-pole captive screw connector.SECTION A–AAAPower SupplyOutput Cord2-Pole Captive S

OperationAfter all devices are connected and powered, the system is fully operational. The FOX T UWP 302 can be configured through SIS commands (see

SIS Configuration and ControlThis section describes remote control of the FOX T UWP 302 through SIS commands and basic installation instructions for t

Safety Instructions • EnglishWARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerou

Error responsesWhen the FOX T UWP 302 receives an SIS command and determines it is valid, it performs the command and sends the corresponding response

X2^= EDID output resolution and refresh rateSee the tables below.VGA - PCSIS ValueResolution Refresh Rate (Hz)SIS ValueResolution Refresh Rate (Hz)SIS

Command and Response Tables for SIS CommandsCommand ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionInput SwitchingInput

Command ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionPicture Adjustment (Analog Only)Pixel phaseSet a pixel phase valu

Command ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionAdvanced ConfigurationInput sync detectionView input sync detecti

Command ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionDevice nameNOTE: No blank or space characters are permitted. Th

Command ASCII Command (Host to Device)Response (Device to Host)Additional DescriptionInternal temperatureView internal temperature20SX!]Internal tempe

FOX Extenders Control ProgramThe Extron FOX Extenders Control Program provides an alternate method to control and configure the FOX T UWP 302. The app

Starting the SoftwareStart the Extron FOX Extenders Control Program as follows:1. Open the FOX Extenders Control Program. The Communication Setup win

Figure 12. Main ScreenThe main screen consists of a top menu, Status panel, Input Selection panel, and Configuration panel.Top MenuThe top menu consi

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rule

ConnectThe Connect option establishes communication with a device. This function re-establishes communication with the device if it times out or enabl

Unit InfoThe Unit Info option opens a dialog box with information about the connected device.Figure 15. Unit Info Dialog Box1. From the Tools menu,

Master System Reset — Resets all unit settings and user settings to factory defaults. From the Tools menu, locate the Reset submenu and select Master

5. Click the Begin button. This uploads the new firmware onto the connected device. The Progress field for the selected device shows the progress of

Help MenuThe Help menu contains options for additional information and reference material, checking for updates to the FOX Extenders Control Program,

About...This option opens a dialog box displaying information about the FOX Extenders Control Program.1. From the Help menu, select About. This opens

Main ScreenThe Main Screen contains status information, input selection, and configuration options.Figure 22. Main ScreenNOTE: The main screen may

Video Indicator — Displays green when the transmitter detects an active signal on the VGA input. Audio Indicator — Displays green when the device dete

VGA Video Adjustment panelThe VGA Video Adjustment panel of the Control tab adjusts the following video parameters on the analog input: horizontal sta

Audio Adjustment panelThe Audio Adjustment panel of the Control tab adjusts the gain and attenuation of analog input audio.Audio Gain and Attenuation

Conventions Used in this GuideNotificationsThe following notifications are used in this guide:WARNING: A warning indicates a situation that has the p

Plus Mode Transmission panelPlus mode can support rates up to 1920x1200 @ 60Hz, with embedded audio, and is HDCP compliant. Non-Plus mode supports rat

Advanced Configuration panelNOTE: This setting is not available for the FOX T UWP 302.EDID Configuration TabEDID is a data structure used to communi

Import EDID panelEDID files can be imported to the FOX T UWP 302 and saved in a table on the device.NOTE: When an EDID file is imported to a user as

Export EDID panelEDID files on the FOX T UWP 302 can be exported to the connected PC. To open and view them, use the Extron EDID Manager software, ava

Reference InformationThis section describes basic installation information of the Extron Firmware Loader program to upload firmware. Topics in this se

Installing Firmware Loader1. Once Firmware Loader has been downloaded, run the .exe file from the save location. The installation wizard window opens

Installing Firmware with Firmware Loader1. Open Firmware Loader and establish a connection between the computer and the device. The Add Device... win

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +

ContentsSIS Conguration and Control ... 13Simple Instruction Set Control ... 13SIS Programming Guide ...

FOX T UWP 302 Wallplate Transmitter • Contents v

IntroductionThis section describes general information about this guide and the FOX T UWP 302 Universal Wallplate Transmitter and selected device feat

Key FeaturesHigh reliability and maximum performance transmission over long distance fiber optic cabling — Transmits HDMI or analog video and stereo a

Application DiagramThe following diagram shows a typical application of the FOX T UWP 302 with two input sources, connected to a fiber optic receiver.