
Command and response table for SIS commands (continued)
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Test pattern
Output color bars
E
1TEST
}
Test1
]
Set the unit to output the color bars test pattern.
Output grayscale
E
2TEST
}
Test2
]
Set the unit to output the grayscale test pattern.
Output crosshatch
E
3TEST
}
Test3
]
Set the unit to output the crosshatch test pattern.
Output alternating pixels
E
4TEST
}
Test4
]
Set the unit to output the alternating pixels test pattern.
Output crop
E
5TEST
}
Test5
]
Set the unit to output the crop test pattern.
Turn test pattern off
E
0TEST
}
Test0
]
Set the unit to output the input video (no test pattern
is selected).
Show test pattern status
E
TEST
} X1$]
View the current test pattern.
Memory presets
Save preset
X1#
, Spr
X1#]
Command code is a comma.
Recall preset
X1#
. Rpr
X1#]
Command code is a period.
Auto memory
Disable auto memory
E
0AMEM
}
Amem0
]
Enable auto memory
E
1AMEM
}
Amem1
]
Default condition.
Show auto memory status
E
AMEM
} X1@]
Audio mute
Mute the audio
1Z
Amt1
]
Silence the audio output of the receiver.
Unmute the audio
0Z
Amt0
]
The receiver outputs audio.
Show audio mute status
Z
X1@]
Audio mute status is
X1@
.
Disable and enable return link and daisy chain
Disable return link
66*0*0#
Rle*0*0
]
Disable link 2.
Enable return link to
transmitter
66*0*1#
Rle*0*1
]
Enable link 2 (default setting).
Enable daisy chain
66*0*2#
Rle*0*2
]
Enable receiver daisy chain mode.
Show return link and daisy
chain status
66*0#
0*
X1%]
HDCP notification
Enable notification
EN1HDCP}
HdcpN1]
Default condition.
Disable notification
EN0HDCP} HdcpN0]
View notification status
ENHDCP}
X1@]
Video shutdown delay
NOTES: • The Set Video Delay command delays the digital video to help monitors sync correctly during an input rate change.
• Only video is delayed; embedded audio is not delayed.
Set delay
3*
X1^
# Dly
X1^]
Delay video by an interval of
X1^
.
Example:
3*3#
Dly3
]
Delay video by an interval of 0.75 seconds
(3 x 0.25 seconds).
View delay
3#
X1^]
Front panel lockout (Executive mode)
Lock front panel
1X
Exe1
]
Lock all front panel controls except for using the Menu
and Enter buttons to unlock the panel only.
Unlock front panel
0X
Exe0
]
View lock status
X
X1@]
NOTE: X1@ = Lock, Auto memory, mute, and HDCP notification status 0 = off 1 = on
X1# = Memory preset number 01 to 30
X1$ = Test pattern 0
= none
3
= crosshatch
1
= color bars 4 = alternating pixels
2
= grayscale
5 = crop
X1% = Rx link and daisy chain enable 0 = disable both 1 = enable return link 2 = enable daisy chain
X1^ = Video delay 0 = 0 second
(0 plus six steps at 0.25 seconds per step) 1 = 0.25 second 3 = 0.75 second 5 = 1.25 second
2 = 0.5 second* 4 = 1.0 second 6 = 1.5 second
* = default
FOXBOX SR HDMI • Remote Control 25
Comentarios a estos manuales