Extron-electronics MTPX Plus Series User Guide Manual de usuario Pagina 153
- Pagina / 169
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Pinging to Determine the Extron IP Address
The ping utility is available at the Command prompt. Ping tests the Ethernet interface
between the computer and the MTPX Plus switcher. Ping can also be used to determine the
actual numeric IP address from an alias and to determine the web address.
Ping the switcher as follows:
1. On the Windows task bar, click on Start > Run.
2. At the Open prompt, type command.
3. Click the OK button.
4. At the Command prompt, type ping {IP address} and then press <Enter>. The
computer returns a display similar to the one shown in figure 91.
C:\>ping 192.168.254.254
Pinging 192.168.254.254 with 32 bytes of data:
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Reply from 192.168.254.254: bytes=32 time<10ms TTL=128
Ping statistics for 192.168.254.254:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Figure 91. Typical Ping Response
The line Pinging ... reports the actual numeric IP address, regardless of whether you
entered the actual numeric IP address or an alias name.
Pinging to Determine the Web IP Address
The ping utility has a modifier, -a, that directs the command to return the web address
rather than the numeric IP address.
At the Command prompt, type ping -a {IP address} and then press <Enter>. The return
display is similar to the ping response shown in figure 91, except that when you specify the
-a modifier, the line Pinging mail... reports the web IP address rather than the numeric
IP address, regardless of whether you entered the actual numeric IP address or an alias
name.
Configuring the MTPX Plus switcher for Network Use via the ARP Command
The ARP (address resolution protocol) command tells your computer to associate the MAC
(media access control) address of the MTPX Plus switcher with the assigned IP address. You
must then use the ping utility to access the controller, at which point the IP address of the
controller is reconfigured.
Use ARP to configure the IP address as follows:
1. Obtain a valid IP address for the MTPX Plus switcher from your network administrator.
2. Obtain the MAC address (UID #) of the MTPX Plus switcher from the label on its rear
panel. The MAC address should have this format: 00-05-A6-xx-xx-xx.
3. If the MTPX Plus switcher has never been configured and is still set for factory defaults,
proceed to step 4. If not, perform a mode 4 system reset and then proceed to step 4.
For detailed information on reset modes, see “Performing Soft System Resets
(Resets 3, 4, and 5)”.
MTPX Plus Series • Ethernet Connection 147
- MTPX Plus Series 1
- User Guide 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- FCC Class A Notice 3
- Copyright 4
- Trademarks 4
- Contents 5
- Introduction 7
- MTPX Plus 3232 8
- Twisted Pair 8
- Matrix Switcher 8
- TP Cable Advantages 10
- MTP T 15HD A 11
- MTP Transmitter 12
- MTP Receiver 12
- VTT Transmitter 13
- VTR Receiver 13
- Features 14
- Installation 17
- Signal Inputs 18
- Connector 19
- Unbalanced Stereo Input 20
- Balanced Stereo Input 20
- Do not tin the wires! 21
- Signal Outputs 22
- Mono Output 23
- Remote Connection 24
- Ethernet Connection 25
- Reset Button 26
- Power Connection 26
- Operation 28
- MTP MATRIX SWITCHER 29
- Input and Output Buttons 30
- Control Buttons and LEDs 32
- I/O Controls 34
- 2928 30 31 32 35
- Definitions 36
- Front Panel Security Lockouts 36
- Creating a Configuration 37
- 1 2 3 4 5 6 7 8 15 16 38
- 17 18 19 20 21 22 23 24 31 32 38
- VIDEO AUDIO 40
- 1 2 3 4 5 6 7 8 16 41
- 17 18 19 20 21 22 23 24 32 41
- Viewing the Configuration 42
- I/O Grouping 45
- C O N T R O L 46
- Press the button 48
- Using Presets 49
- 1 2 3 4 15 16 50
- 17 18 19 20 31 32 50
- No noticeable 54
- MTPX Plus 1616 54
- MTPX Plus 816, 168, 1616 56
- MTPX Plus 128 56
- Press and hold 57
- 2 seconds 57
- Reading the displayed volume 60
- 17 18 12 63
- 1 2 3 4 12 13 14 15 16 63
- 17 18 19 27 28 29 30 31 32 63
- 1 3 4 5 6 7 8 9 64
- VIDEO AUDIO 65
- File > Save 66
- MATRIX settings as 66
- 1 2 3 16 67
- 17 18 19 32 67
- Press an 69
- Rear Panel Operations 70
- Table 7 71
- Reset Mode Comparison/Summary 71
- Optimizing the Audio 73
- Video Adjustments 73
- Troubleshooting 73
- Configuration Worksheets 74
- Weekly status mtg 3 75
- Programming 79
- Local Host-Control Ports 80
- Ethernet (LAN) Port 81
- Host-to-Switcher Instructions 82
- Switcher-initiated Messages 82
- Switcher Error Responses 83
- } character) 84
- : 0*! clears all ties 86
- (Host to Unit) 87
- (Unit to Host) 87
- Audio output volume 90
- Symbol definitions 99
- Command Function 100
- SIS Command 100
- Response 100
- Additional description 100
- IP setup commands 100
- IP setup commands (continued) 101
- Matrix Software 102
- Installing the Software 103
- Ethernet protocol settings 104
- Finish to exit the wizard 105
- (no Icons or Ties) 108
- IP Settings/Options window 109
- Address and Name fields 110
- Hardware Address field 111
- Use DHCP check box 111
- Sync Time to PC button 111
- E-mail Addressee fields 112
- Updating the Firmware 113
- OK to continue 115
- Begin (see figure 61) 117
- Uploading HTML Files 118
- Windows menus 119
- File menu 119
- Tools menu 120
- Fan is operating properly 123
- Fan has failed 123
- The MTPX Plus fans will 123
- Installed” status 123
- Preferences menu 124
- Using Emulation Mode 125
- Using the Help System 126
- Optimizing the Video 127
- MTPX Skew Setting 128
- MTPX Plus Pre-Peak Selection 129
- C:\Program Files\Extron\ 130
- ButtonLabelGenerator 130
- Start > Programs > 131
- HTML Operation 132
- Download the Startup Page 133
- Status Tab 134
- Select Passwords 135
- Select Firmware Upgrade 135
- Select Email Settings 135
- Date/Time Settings fields 137
- Setting up SMTP authorization 140
- Domain Name field 140
- Email Address fields 140
- File Management Tab 142
- Picture Settings 143
- I/O Settings 143
- Global Presets 143
- MTPX Configuration 143
- Set and View Ties 144
- Changing the skew 145
- Ethernet 152
- Connection 152
- Microsoft Telnet> 155
- Subnetting — A Primer 157
- Reference 159
- Information 159
- Part Numbers and Accessories 163
- Optional Accessories 164
- Mounting the Switcher 165
- Mounting Instructions 166
- Button Labels 167
- Extron Warranty 169
Relacionado con productos y manuales para Accesorios de audio Extron-electronics MTPX Plus Series User Guide
Accesorios de audio Extron-electronics MTPX Plus 6400 Series User Guide Manual de usuario
(166 paginas)
(166 paginas)
Accesorios de audio Extron-electronics MAV Plus series Large Scale Setup Guide Manual de usuario
(21 paginas)
(21 paginas)
Accesorios de audio Extron-electronics CrossPoint Plus Matrix Switchers 84, 88, 124, 128, Manual de usuario
(72 paginas)
(72 paginas)
Accesorios de audio Extron-electronics MAV Plus series Large Scale User Guide Manual de usuario
(186 paginas)
(186 paginas)
Accesorios de audio Extron-electronics RCP 2000 with ISS 506 Support Upgrade Kit Manual de usuario
(2 paginas)
(2 paginas)
Accesorios de audio Extron-electronics RCP 2000 with ISS 506 Support Setup Guide Manual de usuario
(4 paginas)
(4 paginas)
Accesorios de audio Extron-electronics XTRA Full Rack Series Setup Guide Manual de usuario
(2 paginas)
(2 paginas)
Comentarios a estos manuales