Extron electronics DP DA2 Guía de usuario

68-2154-01 Rev. B10 12DP DA2User GuideDisplayPortDistribution Amplifier

Rear Panel FeaturesPower SupplyThe provided 12 VDC power supply connects to this 2-pole, 3.5mm captive screw connector. The front panel power LED lig

Display Port ConnectorsConnect the source device to the input socket and up to two display devices to the output sockets. The connector wiring is show

Dual Mode DisplayPortThe DP DA2 supports dual mode for interoperability with VGA, DVI, and HDMI display devices. Appropriate adapters are required.NOT

DIP switchesTwo DIP switches are used to select which of two EDID values is presented to the source device (DIP switch 1) and whether the output is in

RS-232 ControlThe RS-232 controls use the first three pins of the rear panel 5-pin captive screw connector labeled “Remote”. The pins are labeled Tx, R

Front Panel FeaturesPower LEDThe Power LED lights green when the unit is receiving power.Config USB PortConnecting to the USB PortThe mini type B USB p

2. If this is the first time a DP DA2 has been connected to the PC, the Found New Hardware Wizard opens. The first screen offers to search the web for

4. Select Install the software automatically (Recommended) and click Next.NOTE: You do not need to insert an installation disc.The PC locates the dr

SetupThis section provides an overview of how to connect and configure the DP DA2.1. Place the DP DA2 in a suitable location.2. If necessary, connect

SIS CommandsThis section provides information about the Extron Simple Instruction Set (SIS™) commands that are used to configure the DP DA2.• Introduc

Safety Instructions • EnglishWARNING: This symbol, D, when used on the product, is intended to alert the user of the presence of uninsulated dangerou

Symbols Used in this GuideWhen programming in the field, certain characters are conveniently represented by their hexadecimal rather than their ASCII v

Command and Response Table for SIS Commands Command ASCII Command(host to unit)Response(unit to host)Additional DescriptionVideo MuteVideo mute single

Updating FirmwareUpdates to the DP DA2 firmware are released periodically on the Extron website. You can find the version that is currently loaded on yo

Downloading DP DA2 FirmwareTo obtain the latest version of firmware for your DP DA2:1. Visit the Extron website (www.extron.com), click the Download t

Loading the Firmware to the DP DA2To load a new version of firmware to the switcher using Firmware Loader, connect your computer serial port to the firs

9. On the Open window, navigate to the new firmware file, which has an S19 extension, and double-click it.Figure 11. Open Window for Firmware File Sel

10. On the Add Device window, the path to the new firmware file is displayed in the Path field.Figure 12. Path to the New Firmware File on the Add Devic

Figure 13. Firmware Loader Screen with a DP DA2 Added12. If you want to remove a device from the Devices section, do the following:a. Click on the n

Reference InformationIncluded PartsDescription Part NumberDP DA2 60-1221-0112 VDC, 1 A Power SupplyIEC cord(4) Rubber feet(1) 3.5 mm, 5-pole captive s

MountingDesktop PlacementAttach the four provided rubber feet to the bottom of the unit and place it in any convenient location.Rack MountingUL Guidel

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +

Conventions Used in this GuideNotifications the following are used:ATTENTION: Attention indicates a situation that may damage or destroy the product

ContentsSafety Instructions ... iiIntroduction... 1About

DP DA2 • Contents vi

IntroductionThis guide describes the function, installation and operation of the DP DA2 distribution amplifier. Unless otherwise stated, the terms “DA”

HDCP visual confirmation — Provides a green signal when encrypted content is sent to a non-compliant display. A full-screen green signal is sent when H

Panel FeaturesThis section describes the panel features and connections of the DP DA2.Rear Panel12V0.6A MAXPOWEREDIDSTOREEXTENDNORMALDEFAULTSTORED1RS-