Extron electronics VN-Matrix 325 Guía de usuario Pagina 26
- Pagina / 78
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LAN Port Specific Options
Option Function Comments
4 and 14 gateway:
Set the IP address of
the default gateway.
• Gateway values must be set on the streaming port otherwise
no streaming status is available in the HTML network
interface. The default gateway must be on the same subnet
as the port to which it is assigned.
Manually enter the gateway address for the port; use
no leading zeroes. For example: 192.168.0.1 is valid,
192.168.000.001 is not valid.
NOTE: Only one default gateway is supported. Once a
gateway is assigned to either LAN port (either
option), the unselected option is no longer
available. To clear a gateway address, select the
available option (4 or 14) and press the <Enter>
key with no gateway value entered.
5 and 15 broadcast:
Not required.
6 and 16 mtu:
Set the maximum
the number of bytes
(payload) in a frame.
• This value affects the performance of the system. A large
value can cause packets to be fragmented; a small value may
not make efficient use of the network capacity.
• The default value is 1500. In certain cases, you may need to
change this value to better match the network.
Unit Specific Options
Option Function Comments
7 controller ip:
Set the IP address of
the system controller.
• Enter the IP address of the LAN port (option 2 or 12) over
which control data is sent to the VNC 325 that is designated
as the controller into all codecs in the system.
NOTES: • For proper operation, option 7 in all codecs
must have the same IP address.
• Once you have designated a codec as the
controller using option 7, you can access it via
either of its LAN ports.
• Manually enter the IP address for the controller; use
no leading zeroes. For example: 192.168.0.1 is valid,
192.168.000.001 is not valid.
17 ip forwarding:
Not implemented. Do not change this value.
8 controller port:
Set the number of
the port that is used
for communications
with the system
controller.
By default this is set to 5432, this can be changed if required.
NOTE: For proper operation, option 8 in all codecs must
have the same port number.
18 webserver port:
Set the port number
that is used for
communication with
the server.
By default this is set to 80, this can be changed if required.
NOTE: For proper operation, the browser must use the
same port number.
9 Exit
Reboot and activate
settings.
Activate any changes made by rebooting the codec.
Changes are not activated until the codec is rebooted.
NOTE: Entering reboot at the terminal emulation program
cursor also resets the unit.
VN-Matrix 325 Serial Digital Over IP CODEC • Installation and Setup 20
- User Guide 1
- VN-Matrix 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- FCC Class A Notice 3
- Copyright 4
- Trademarks 4
- Contents 5
- Introduction 7
- Features 9
- Installation and 11
- Rear Panel Features 12
- Mounting the Units 13
- Data Transport Methods 14
- Unicast RTP 15
- Data and Control Routing 16
- VN-MATRIX 325 SERIES 17
- Configuring Network Settings 22
- Configuration Selections 25
- OVER LAN 27
- RJ-45 port wiring 28
- Encoder configuration 29
- Decoder configuration 30
- Startup and Login 31
- Enable multicast streaming 36
- Operation 37
- Network Interface 38
- Device List Page 39
- Device summary panel 41
- Licensed features panel 41
- Device setup panel 42
- Configuration panel 42
- Streams panel 43
- Name panel 44
- ANC (Audio) panel 45
- Standard 48
- Destination Trans BW(Mbps) 49
- Advanced Controls panel 50
- Video Quality Management 50
- Bandwidth Management 51
- Typical bit rates 52
- Firmware Upgrade Page 59
- Browse button ( 61
- Open button ( 61
- License Page 62
- Passwords Panel 63
- Clock Management Panel 64
- Controller Licensing Panel 64
- Alarms and SNMP 65
- Filter settings panel 66
- Alarm list panel 67
- Alarm types and descriptions 67
- • Has the unit been 68
- • Is power applied? 68
- • Are the network 68
- Alarm Logs page 69
- SNMP Password Value 70
- SNMP Community Value 71
- SNMP Trap Destination Values 71
- Reference 72
- Information 72
- Network transport 74
- Part Numbers and Accessories 75
- Mounting the Codec 76
- Test Pattern 77
- Extron Warranty 78
(16 paginas)
Comentarios a estos manuales