Extron-electronics Cable Retraction System Setup Guide Manual de usuario descargar pdf (Pagina 1)

IMPORTANT:

Refer to www.extron.com for

the complete user guide and

installation instructions.

This guide provides basic instructions for an experienced

technician to install the Extron Cable Retraction System

for CableCubby

Enclosures. Additional instructions

are available in the Cable Retraction System User Guide

available online at www.extron.com.

Planning

The cable retraction system can be mounted horizontally or vertically depending upon under‑table clearance and accessibility.

The XL models, which provide additional cable length, can also be mounted at an angle. Where differences occur in mounting,

they will be noted.

Horizontal mounting is recommended to provide maximum legroom and to protect the retractors against accidental damage.

Vertical mounting is used where insufcient under‑table space exists for horizontal mounting or where under‑table access is

limited.

Angular mounting (XL models only) is used where insufcient under‑table space exists for horizontal mounting and tabletop

to oor clearance prevents vertical mounting. The XL enclosure has additional mounting holes that enable mounting at an angle

between vertical and horizontal.

• For horizontal mounting, a mounting bracket kit, part number 70-678-00, is required.

• Filler modules, part number 70-678-08, may be required to occupy unused retractor space.

• For Cable Cubby200 applications, the CC200 Mounting Bracket Kit, part number 70-678-10, is required. Mounting

instructions are included with the kit and are also available online.

• For DC Power retractors, refer to the list on the website for laptop compatibility. Always use a power supply recommended

by the laptop manufacturer.

Kits and ller modules are available at www.extron.com.

For new installations, to determine the best location for the enclosure, keep in mind the under‑table space required for the

retraction system. Once the optimal mounting location for the CableCubby is determined, follow the instructions for cutting a

hole in the table (if necessary) and mounting the enclosure. Then install the retractors, AAP brackets, AAPs, and power module.

NOTE: When AAP modules are relocated or removed to provide space for the retraction system, associated

AAP brackets may require reconfiguration or replacement. Before starting an installation, determine if

replacement AAP brackets will be needed. Replacement brackets may be ordered from the Extron website.

If there will be no under‑table access after the Cable Cubby enclosure is mounted, the retraction system must be installed before

the enclosure is mounted (see “Alternative Solution — Drop-in Installations” on page8). Otherwise the enclosure may be

congured and mounted, then the retraction system installed from underneath.

Required Tools and Additional Accessories

Cable Retraction System • Setup Guide

Cable Retraction System • Planning and Tools

Horizontal Mounting

Bracket (Optional)

Part #70-678-00

Filler Module

(Optional)

Part #70-678-08

CC 200

Mounting Bracket

(Optional)

Part #70-678-10

Tape Measure

Hex Nut Driver

(10 mm)

Phillips Screw Driver

Zip Ties

Marker Pen

Tweeker

(x4)

HDMI Cable

Audio Cable

Network Cable

Extron

Retractor

Cable Retraction System for

Cable Cubby

Enclosures

Mounted in

Horizontal Position

in Cable Cubby 300C

Horizontal Mounting

Bracket (Optional)

1 2 3 4 5 6 7 8 9 10

Indice de contenidos

Pagina 1 - Planning

1IMPORTANT:Refer to www.extron.com for the complete user guide and installation instructions.This guide provides basic instructions for an experienced

Pagina 2 - For retroﬁt installations:

Planning (page 1)  Ensure there is adequate space available in the Cable Cubby enclosure.  Obtain the mounting brackets and accessories necessary f

Pagina 3 - Product Category

2Cable Retraction System • Setup Guide (Continued)Getting Started — Determine Under-table ClearancesThe diagrams below and on the next page show the

Pagina 4 - Retroﬁt installations:

3Product CategoryTop ViewHorizontalBracketUNSWITCHED100-240V/ 5AMAXUNSWITCHEDUSP HUB4 AAPACTIVITY100-240V/ 5AMAXAll installations (Except Drop-In):Th

Pagina 5

4Cable Retraction System • Setup Guide (Continued)Getting Started — Prepare the EnclosureAll installations:By now you should be certain the retractio

Pagina 6 - Installation

5Product CategoryCable Retraction System • Getting StartedRemove two enclosure screws (front and back) from this position for horizontal or angular (

Pagina 7 - Horizontal Bracket Mounting

6Cable Retraction System • Setup Guide (Continued)Cable Retraction System • InstallationInstallationThe enclosure must be installed and properly con

Pagina 8 - Locking Screw (Optional)

7Product CategoryHorizontal Bracket MountingTrace aroundbracket perimeter.Mounted inHorizontal Position4. Lower the assembly and remove the horizont

Pagina 9 - Retractor Operation

8Cable Retraction System • Setup Guide (Continued)Alternative Solution — Drop-in InstallationsWhen installing the retraction system where under‑table

Pagina 10 - Quick Installation Checklist

9Product CategoryCable Retraction System • Retractor OperationRetractor OperationOnce installed, the retractors are ready for regular operation.CAUTI

Comentarios a estos manuales

Sin comentarios

Extron-electronics Cable Retraction System Setup Guide Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Hardware Extron-electronics Cable Retraction System Setup Guide. Extron Electronics Cable Retraction System Setup Guide User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Extron-electronics Cable Retraction System Setup Guide Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Hardware Extron-electronics Cable Retraction System Setup Guide. Extron Electronics Cable Retraction System Setup Guide User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Extron-electronics Cable Retraction System Setup Guide