Extron-electronics DVI 201xi Tx User Guide Manual de usuario Pagina 19
- Pagina / 26
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Setup and Operation
1. Determine which display device will provide the EDID information and configure the
DDC switches appropriately (see DDC Switches on page 6 and Conguring EDID on
page 10). If necessary, use the EDID Minder to read and store information from a display
(see Conguring EDID on page 10).
2. Prepare twisted pair cables (see Terminating shielded cable on page 7).
3. Select a receiver that is compatible with the DVI 201xi Tx and connect it to the
transmitter (see Twisted Pair Cable Connections on page 9).
4. Connect the source device to the transmitter (see DVI-D input on page 5). Do not
power on the source device at this time.
5. Connect the display device to the receiver (see the user guide for the receiver). If
required, connect a local monitor to the transmitter (see Local monitor output on
page 5).
6. If required, connect any RS-232 or IR control devices (see Control Signal Pass-through
on page 6).
7. Connect the power supply to the transmitter (see Power Input on page 4 or the user
guide for the receiver). If required, connect a second power supply to the receiver. The
receiver can obtain power remotely from a power supply connected to the transmitter.
8. Power on the display device.
9. Power on and boot up the source device.
Troubleshooting
If the DVI 201xi Tx does not provide a high quality output signal, check the following
possibilities before contacting your Extron representative (see back cover for contact
information). Be sure to read all the suggestions as many of the issues have several possible
solutions.
No output signal — Check that the front panel LEDs for both the transmitter and receiver
are lit. The transmitter LED lights amber when it is receiving power. If it is not, check the
power supply connections to the units.
If a single power supply is supplying power to both units, it must be connected to the
transmitter. Ensure both twisted pair cables are firmly seated in the correct ports.
No output signal or poor quality signal — Check the integrity of the UTP or STP cables
between the transmitter and the receiver.
Ensure that the twisted pair cables are terminated correctly and to the same standard at
both ends (see Terminating shielded cable on page 7).
Ensure that each RJ-45 connector is firmly seated in its receptacle and that each
transmitter port is connected to the correct receiver port (see Twisted Pair Cable
Connections on page 9).
Ensure that the length of the TP cable does not exceed the guidelines for single link
connections (see Single Link DVI transmission distances on page 9).
DVI 201xi Tx • Conguration and Operation 13
- DVI 201xi Tx 1
- User Guide 1
- Precautions 2
- FCC Class A Notice 3
- Copyright 3
- Trademarks 3
- Contents 5
- DVI 201xi Tx • Contents vi 6
- Introduction 7
- DVI 201xi Tx • Introduction 2 8
- Panel Features 9
- Power Input 10
- DVI-D Input and Output 11
- EDID Minder 12
- DDC Switches 12
- Control Signal Pass-through 12
- Twisted Pair Output 13
- Pair Wires 14
- Configuration and 16
- Operation 16
- 1 2 3 17
- DEFAULT EDID 18
- EDID MINDER 18
- REMOTE DDC 18
- Setup and Operation 19
- Troubleshooting 19
- Specications 21
- Reference 23
- Information 23
- Mounting 24
- Extron® Warranty 25
- Installation Checklist 26
Relacionado con productos y manuales para Accesorios para vídeo Extron-electronics DVI 201xi Tx User Guide
Accesorios para vídeo Extron-electronics DMS 1600_2000_3200_3600 User Guide Manual de usuario
(121 paginas)
(121 paginas)
Accesorios para vídeo Extron-electronics DVI DA Plus Series Setup Guide Manual de usuario
(2 paginas)
(2 paginas)
Comentarios a estos manuales