Extron-electronics FOX 500 DVI Tx User Guide Manual de usuario descargar pdf (Pagina 12)

FOX 500 Tx/Rx • Installation

Installation, cont’d

2-6

FOX 500 Tx/Rx • Installation

2-7

a. Mark the location of the brackets relative to the screws.

b. Remove the transmitter or receiver from inside the

furniture.

c. Tighten the screws.

d. Replace the unit inside the surface (step 6).

Connections

Transmitter rear panel connections and settings

All connectors except the Conguration port are on the rear

panel (gure 2-4).

FOX 500 Tx

100-240V 0.3A

50/60 Hz

AUDIO INPUTS

INPUT LOOP THRU

RGB INPUT

RGB

H/HV V

RS-232

OVER FIBER

Tx Rx NA

REMOTE

RS-232

ALARM

OPTICAL

12*

OPTIONAL FOR

RETURN DATA

LINK

Tx Rx 1 2

RGB

FOX 500 DVI Tx

100-240V 0.3A

50/60 Hz

AUDIO INPUTS

RS-232

OVER FIBER

Tx Rx NA

REMOTE

RS-232

ALARM

OPTICAL

12*

OPTIONAL FOR

RETURN DATA

LINK

Tx Rx 1 2

DDC

RESOL

DVI - D INPUT

LOOP - THRU

1011 8

1 6

1053 411 8

Figure 2-4 — FOX 500 Tx

transmitter’s connectors

Connect an active

input to only the

BNC connectors

or the 15-pin HD

connector, not

both.

RGB Input connectors

(FOX 500 [RGB] only) —

BNC connectors — Connect

an RGBHV, RGBS, RGsB, or

RsGsBs video source to these

BNC connectors. Connect the

cables as shown at right.

15-pin HD connector — Connect an analog VGA - UXGA RGB

video source to this 15-pin HD female connector.

Buffered Loop-through connector (FOX 500 [RGB] only) —

If desired, connect a local monitor to this 15-pin HD connector.

DVI-I Input connector (FOX 500 DVI only) — Connect a single

link of DVI-D to this DVI-I connector. See "DVI connector

(FOX 500 DVI)" on page 2-15

for pin assignments.

The FOX 500 DVI accepts only the digital signals on

the DVI-I Input connector. The analog pins on the

port are not connected.

DDC Resol (ution) rotary switch (FOX 500 DVI only) — Set

this switch to one of the positions below to select the source of

the DDC or a specic resolution.

• Position 0 — The loop-through monitor (item

, below)

is the source of the Display Data Channel (DDC)

• Position 1 — The DDC is selected either from the front

panel (using the menu system) or via one of the system's

serial ports (using an SIS command or the Windows-

based control program).

• Position 2 - F — Specify a resolution. The table below

identies the switch positions and the associated

resolutions. The vertical refresh rate for all resolutions is

60 Hz with the exception of the 576p resolution, which is

50 Hz.

Pos. Pos. Pos.

Source or

Resolution

Resolution Resolution

Local monitor 1280 x 1024 576p

RS-232/menu 1365 x 768 720p

1920 x 1200 1366 x 768 1080i

800 x 600 1400 x 1050 1080p

1024 x 768 1600 x 1200

B1280 x 768 480p

Buffered Loop-through connector (FOX 500 DVI only) —

If desired, connect a local monitor to this DVI-I connector.

See "DVI connector (FOX 500 DVI)" on page 2-15

for pin

assignments.

RGBHV

H/HV V

RGBS

RGsB,

RsGsBs

RGB

H/HV V

RGB

H/HV

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 45 46

Comentarios a estos manuales

Sin comentarios

Extron-electronics FOX 500 DVI Tx User Guide Manual de usuario Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios para vídeo Extron-electronics FOX 500 DVI Tx User Guide