EDID Minder
The EDID Minder has two modes; a preset mode and a learn mode.
Preset mode allows selection of pre-programed EDID rates, as shown in the table below.
Learn mode enables the displays specific EDID information to be recorded and emulated
by the input wallplate.
To use the EDID Minder mode in preset or learn Mode, follow the instructions below.
Using Preset mode
1. If already installed, disconnect any sources and displays from the front panel and
remove the wallplate from the wall.
2. On the rear panel, set DIP switch 1 to the 50 or 60 kHz setting as desired.
Set DIP switches 2 to 5 accordingly, to match the desired EDID rate (see table below).
3. Connect the video source to the “Computer In” VGA connector and a local display
device to the “Monitor Out” port.
4. Restart the video source and display devices. Verify the image, making any
changes to the EDID settings as needed.
5. When the image is correct, re-install the wallplate. Re-connect and restart the source and display devices.
Preset
Number
Switch setting
Resolution
2 3 4 5
0 Off Off Off Off Learn mode
1 Off Off Off On 800 x 600
2 Off Off On Off 1024 x 768 (default)
3 Off Off On On 1280 x720
4 Off On Off Off 1280 x 768
5 Off On Off On 1280 x 800
6 Off On On Off 1280 x 1024
7 Off On On On 1360 x 768
8 On Off Off Off 1366 x 768
9 On Off Off On 1400 x 1050
A On Off On Off 1440 x 900
B On Off On On 1600 x 1200
C On On Off Off 1680 x 1050
D On On Off On 1920 x 1080
E On On On Off 1920 x 1200
F On On On On N/A
Using Learn mode
1. Disconnect any sources from the front panel and remove the wallplate from the wall.
2. On the rear panel, set all the DIP switches to off (down).
3. Temporarily connect the main display device (the projector) to the “Monitor Out” port.
4. On the front panel, the learn LED is lit solid green. Press and release the Learn button.
5. The LED flashes red when in learn mode, then returns to solid green when complete.
6. Re-install the wallplate and reconnect the source device.
Connect a local display device to the “Monitor Out” port as needed.
7. Reconnect the projector to the PoleVault switcher. Restart the source and display devices.
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
+971.4.2991800
+971.4.2991880 FAX
68-1823-50
Rev B
10 10
©2010 Extron Electronics. All rights reserved - www.extron.com
COMPUTER IN
AUDIO
IN OUT
MONITOR OUT
IR OUT
S G
EDID Learn
Status LED
EDID Learn
Button
EDID
Selection
60
Hz
50
1 2 3
4
ON
5
NOTE This setting is for 1024x768@60 Hz,
preset 2 (factory default)
2
PVT RGB D Plus (EDID) • Setup Guide, cont’d
(54 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales