Extron-electronics SMX System User Guide Manual de usuario Pagina 14
- Pagina / 124
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SMX System MultiMatrix Switcher • Installation and Cabling 8
Reset button and Ethernet cable termination
It is essential that the Ethernet cables used be the correct type of cable and terminated with
the correct pinout. The cable can be terminated as either a patch cable or a crossover cable
and must be properly terminated relevant to the application (see Ethernet Control on
page 106 for termination details).
c
Reset button (recessed) — Press and hold in this recessed button to reset the
SMX to the default (factory setting) mode. The lit (green) LED blinks once.
d
Remote port — Connect a host device, such as a PC or touchpanel control, to the
SMX via this 9-pin D connector for serial RS-232 or RS-422 control.
Pin RS-232 Function RS-422 Function
1 — Not used — Not used
2 Tx Transmit data Tx Transmit data (-)
3 Rx Receive data Rx Receive data (-)
4 — Not used — Not used
5 Gnd Signal ground Gnd Signal ground
6 — Not used — Not used
7 — Not used Rx+ Receive data (+)
8 — Not used Tx+ Transmit data (+)
9 — Not used — Not used
Figure 3. Remote Port Pin Assignments
NOTES:
• See SIS Configuration and Control on page 34 for SIS command definitions
or SMX Control Software on page 59 control software details.
• The SMX can support either RS-232 or RS-422 serial communication protocol,
and can operate at 9600, 19200, 38400, or 115200 baud rates
(see Operation on page 13 to configure the RS-232/RS-422 port).
Input and Output Boards
The I/O boards on any unit may vary with each installation, depending on desired
configuration and use. All board types have the input and the output connectors clearly
marked, and each board has a 16-position rotary switcher (see m, figure 2) for setting the
I/O plane address. An LED on the board indicates when power is present.
NOTE: Boards with the same plane address switch simultaneously.
Figure 2 shows some, but not all, board variations that can be installed into an SMX frame.
Boards have different combinations of input and output connectors, depending on the
specific board installed. To install any board into an SMX frame slot (see SMX Frame and
I/O Board Installation on page 10).
NOTE: Control signal ground pins may be labeled as or “G”. Audio ground pins may
be labeled as or . The wiring and function are the same, whichever way your product
is labeled.
e SMX 44 DVI — Connect DVI single link high resolution digital input devices (up to
1600x1200 @ 60 Hz) or HDTV devices up to 1080p, to any of the DVI-I female input
connectors. Connect suitable digital displays to the DVI-I female output connectors.
DVI-D INPUTS
1
2
3
4
DVI-D OUTPUTS
1
2
3
4
ADDRESS
RS-232 FunctionPin
1
2
3
4
5
6
7
8
9
—
TX
RX
—
Gnd
—
—
—
—
Not used
Transmit data
Receive data
Not used
Signal ground
Not used
Not used
Not used
Not used
51
9
5
9
6
Female
Male
1
6
RS-422 Function
TX
RX
—
Gnd
—
RX+
TX+
—
Not used
Transmit data (-)
Receive data (-)
Not used
Signal ground
Not used
Receive data (+)
Transmit data (+)
Not used
—
RESET
- User Guide 1
- SMX System 1
- www.extron.cn，参见 Extron 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- Introduction 7
- Definitions 9
- Features 10
- Installation and 12
- Power and Control Connections 13
- Input and Output Boards 14
- ADDRESS 15
- Other I/O Boards 16
- Installing the I/O Boards 16
- Reconfig 17
- Wiring the Audio Connectors 18
- Operation 19
- I/O Plane Selection Buttons 20
- Input and Output Buttons 20
- Control Buttons 21
- Power Indicator LEDs 21
- Powering Up 22
- Front Panel Operation 22
- Creating Ties 23
- Viewing Ties 24
- Removing Ties 25
- Replacing Ties 26
- Muting an output 27
- Unmuting an output 28
- All buttons extinguish 29
- (here preset 8, 18, and 32) 29
- Plane button lights green 30
- C O N T R O L 31
- Using the Front Panel 33
- Using Reset Levels 37
- Modes 3, 4, and 5 38
- Troubleshooting 39
- SIS Configuration 40
- Connection Timeouts 41
- Number of Connections 41
- Using Verbose Mode 41
- SIS Programming Guide 42
- Switcher Error Responses 43
- reference 46
- SIS value 47
- Resolution Refresh (Hz) 47
- X2@*X1$ 49
- 1 = on 49
- 00 52
- nnnn = actual rate 55
- 01 = bypass the reclocker 55
- Verbose mode 2 and 3 58
- 0 = Off or disabled 58
- –12.0 - +14.0 59
- queries 60
- X8# = I, then X8$ = 00 61
- (SMX-00-02-3D) 62
- 00 = fan and power supply 64
- SMX Control 65
- Software 65
- Starting the Program 66
- Using Emulation Mode 67
- Using the Program 68
- File menu 69
- Tools Menu 70
- Audio-input-Config 77
- Preferences 78
- Master-Reset 80
- Customizing the SMX Window 81
- Managing Ties 82
- IP Settings/Options 83
- Setting the IP address 84
- Setting the subnet mask 85
- Hardware address field 85
- Enabling daylight saving time 87
- Setting the user password 87
- Updating the firmware 89
- Uploading HTML files 91
- HTML Configuration 93
- System Status Pages 95
- Physical Configuration 96
- Configuration Pages 97
- Date/Time Settings fields 99
- Passwords Page 100
- Email Settings Page 100
- Email Address Fields 101
- Firmware Upgrade Page 102
- File Management Page 103
- Control Pages 104
- To set or replace ties 105
- To remove ties 105
- To set input audio levels 106
- To set output volume levels 107
- To mute or unmute a signal 108
- EDID configuration 109
- Presets Page 110
- Recalling a global preset 111
- Recalling a plane preset 111
- Ethernet Control 112
- Connect as a Telnet Client 115
- Telnet tips 116
- Escape character and Esc key 116
- Local echo 116
- Subnetting — A Primer 117
- Subnet Masks and Octets 118
- Reference 119
- Information 119
- Button Labels 120
- Replacing Button Labels 122
- Button Label Blanks 123
- Contact Information 124
- Extron Warranty 124
(1 paginas)
(2 paginas)
(59 paginas)
Comentarios a estos manuales