Extron electronics Matrix 200 Guía de usuario descargar pdf (Pagina 64)

Figure 42. Setting the EDID Mode

To set the EDID mode, perform the following steps:

1. From the web interface, select the VN-Matrix defined as an encoder (source) device.

2. Click the videoPort0 icon.

3. Click the Configure tab.

4. Select the appropriate EDID mode. In most cases, Transparent will be the correct

option. This will allow the EDID data of the display to pass through the matrix to the

source PC.

5. Reboot the source PC to ensure it reads the proper EDID selection.

VN-Matrix 200 Series • Advanced Setup Procedures 59

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 122 123

User Guide 1
VN-Matrix 1
200 Series: 1
VNC 200 DVI, VNE 200 DVI, and 1
VND 200 DVI 1
Safety Instructions • English 2
安全须知 • 中文 2
Copyright 3
Trademarks 3
Contents 4
Introduction 6
Firmware Version 7
Product Range 7
Functional Overview 8
Decoder Display Capability 9
Control Capability 9
Network Requirements 9
Example System Application 10
Data Transport Methods 10
SOURCE DISPLAY 11
SOURCE DISPLA 12
VN-MATRIX 200 SERIES 13
RGB/DVI OVER IP 13
Rear Panel Features 14
Installation 15
Procedure 15
Mounting Requirements 16
Power Connection via PSU 17
Power Cord for PSU 18
External Supply Protection 19
Network Communications Setup 20
To access the setup menus… 21
Connect Devices 24
Connecting a digital source 25
SOURCE COMPUTER 26
Connecting a digital display 27
Connecting an analog display 28
Device List Page 31
Save All tab 32
Additional Setup for Audio 35
EDID options 36
Identify Mode 36
Audio status 37
Advanced setup options 38
Help tab for details 39
Help tab 39
Save All tab as shown above 40
Identify mode 41
Nodata Splash Mode 43
Device mode 44
Troubleshooting 45
Source Checkup 47
System Checkup 48
Controller Checkup 49
Serial Transport 50
TCP RS-232RS-232 TCP 51
Serial / Telnet Commands 52
Device Commands 53
Data Stream Mode 54
Remote Keyboard 56
Operation 56
Mouse and Keyboard Control 57
Mode = Enable 59
Advanced Setup 60
Procedures 60
Video Setup Page 61
Custom Input Modes 63
Configure tab 64
Creating a custom input mode 65
VideoPort icon b 67
Video Setup tab c 67
Bandwidth (Source) Page 69
Figure 45. Bandwidth Page 70
Bandwidth Management 71
Setting the maximum bit rate 72
Setting the video quality 72
Transform setting 73
Quality Control settings 74
Temporal compression setting 74
Monitoring the bit rate 75
Audio Compression 76
Decoder Set Up 77
Adjusting the Playback Delay 79
Custom Output Modes 80
Creating a CVT output mode 81
Creating a custom output mode 81
Parameter Meaning 82
Controller Configuration 84
Controller Licensing 85
Upgrading Device Firmware 85
Changing a Device Licence 88
Update Licence button 89
Alarms and SNMP 90
Alarms Page 91
Apply Filter Change 92
Save All tab is used to make 92
Alarms tab is selected 92
Alarm Logs 93
Overview – SNMP 96
SNMP Trap Destinations 97
IP Addressing 98
Choosing IP Addresses 99
Subnet Mask 100
Response Messages 100
Understanding 102
Network 102
Performance 102
Nodes, Switchers, and Routers 103
Protocols 103
Browser 106
Conﬁguration 106
To enable JavaScript: 107
Mozilla (v1.3 or Above) 108
Technical Data 110
DVI Input (IN) 111
DVI Output (OUT/LOOP) 113
Network (1 and 2) 115
RS-232 Port Settings 116
Serial Port Login Procedure 117
Command options 117
Starting Telnet 118
Login Procedure 118
Reference 119
Information 119
Accessories 122
Extron® Warranty 123
Warranty 123

Comentarios a estos manuales

Sin comentarios

Extron electronics Matrix 200 Guía de usuario Pagina 64

Comentarios a estos manuales

Relacionado con productos y manuales para Gateways / Controladores Extron electronics Matrix 200