Extron electronics Matrix 200 Guía de usuario Pagina 90
- Pagina / 123
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Alarms and SNMP
This section describes the following:
• Overview – Alarms
• Overview – SNMP
• SNMP Trap Destinations
Overview – Alarms
The VN-Matrix system is configured to generate alarms for error conditions. A list of these
error conditions and their meanings are presented on the following pages.
Alarms can be monitored at a number of locations throughout the web GUI
• In the Alarms page
• In the list immediately below the Filter Settings box. This details the alarm
conditions that are currently active on the system.
• In the Alarm Logs page
• In the list immediately below the Filter Settings box. This provides a historical log
of when an alarm condition was raised and cleared.
• In the Device List page
• Where a traffic light system is used to represent the status of a device.
• In the top left hand corner of each page in the web GUI.
• Where the device status and system status is displayed.
In addition the red LED located on the front panel of the VN-Matrix device will illuminate
whenever a critical alarm is triggered.
Alarm conditions, once triggered, will remain active until the error that caused it has
cleared and then for an additional five seconds.
VN-Matrix 200 Series • Alarms and SNMP 85
- User Guide 1
- VN-Matrix 1
- 200 Series: 1
- VNC 200 DVI, VNE 200 DVI, and 1
- VND 200 DVI 1
- Safety Instructions • English 2
- 安全须知 • 中文 2
- Copyright 3
- Trademarks 3
- Contents 4
- Introduction 6
- Firmware Version 7
- Product Range 7
- Functional Overview 8
- Decoder Display Capability 9
- Control Capability 9
- Network Requirements 9
- Example System Application 10
- Data Transport Methods 10
- SOURCE DISPLAY 11
- SOURCE DISPLA 12
- VN-MATRIX 200 SERIES 13
- RGB/DVI OVER IP 13
- Rear Panel Features 14
- Installation 15
- Procedure 15
- Mounting Requirements 16
- Power Connection via PSU 17
- Power Cord for PSU 18
- External Supply Protection 19
- Network Communications Setup 20
- To access the setup menus… 21
- Connect Devices 24
- Connecting a digital source 25
- SOURCE COMPUTER 26
- Connecting a digital display 27
- Connecting an analog display 28
- Device List Page 31
- Save All tab 32
- Additional Setup for Audio 35
- EDID options 36
- Identify Mode 36
- Audio status 37
- Advanced setup options 38
- Help tab for details 39
- Help tab 39
- Save All tab as shown above 40
- Identify mode 41
- Nodata Splash Mode 43
- Device mode 44
- Troubleshooting 45
- Source Checkup 47
- System Checkup 48
- Controller Checkup 49
- Serial Transport 50
- TCP RS-232RS-232 TCP 51
- Serial / Telnet Commands 52
- Device Commands 53
- Data Stream Mode 54
- Remote Keyboard 56
- Operation 56
- Mouse and Keyboard Control 57
- Mode = Enable 59
- Advanced Setup 60
- Procedures 60
- Video Setup Page 61
- Custom Input Modes 63
- Configure tab 64
- Creating a custom input mode 65
- VideoPort icon b 67
- Video Setup tab c 67
- Bandwidth (Source) Page 69
- Figure 45. Bandwidth Page 70
- Bandwidth Management 71
- Setting the maximum bit rate 72
- Setting the video quality 72
- Transform setting 73
- Quality Control settings 74
- Temporal compression setting 74
- Monitoring the bit rate 75
- Audio Compression 76
- Decoder Set Up 77
- Adjusting the Playback Delay 79
- Custom Output Modes 80
- Creating a CVT output mode 81
- Creating a custom output mode 81
- Parameter Meaning 82
- Controller Configuration 84
- Controller Licensing 85
- Upgrading Device Firmware 85
- Changing a Device Licence 88
- Update Licence button 89
- Alarms and SNMP 90
- Alarms Page 91
- Apply Filter Change 92
- Save All tab is used to make 92
- Alarms tab is selected 92
- Alarm Logs 93
- Overview – SNMP 96
- SNMP Trap Destinations 97
- IP Addressing 98
- Choosing IP Addresses 99
- Subnet Mask 100
- Response Messages 100
- Understanding 102
- Network 102
- Performance 102
- Nodes, Switchers, and Routers 103
- Protocols 103
- Browser 106
- Configuration 106
- To enable JavaScript: 107
- Mozilla (v1.3 or Above) 108
- Technical Data 110
- DVI Input (IN) 111
- DVI Output (OUT/LOOP) 113
- Network (1 and 2) 115
- RS-232 Port Settings 116
- Serial Port Login Procedure 117
- Command options 117
- Starting Telnet 118
- Login Procedure 118
- Reference 119
- Information 119
- Accessories 122
- Extron® Warranty 123
- Warranty 123
Relacionado con productos y manuales para Gateways / Controladores Extron electronics Matrix 200
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales