Extron-electronics HDXP Plus Series User Guide Manual de usuario Pagina 42
- Pagina / 125
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
HDXP Plus Series Switchers • Operation 36
Selecting the RS-232 or RS-422 Protocol and Baud Rate
The HDXP switchers can support either RS-232 or RS-422 serial communication
protocol, and operate at 9600, 19200, 38400, and 115200 baud rates. The settings of
these variables can be viewed and changed from the front panel.
NOTE: This information applies to only the rear panel Remote RS232/RS422 port.
The front panel Config port is RS-232 only; RS-422 cannot be selected for it.
View and configure the serial communications settings as follows:
1. To enter serial port configuration mode, simultaneously press and hold all Control
buttons (Enter, Preset, View
<
, and Esc
>
) until all buttons light (approximately
2 seconds).
C O N T R O L
PRESET
ENTER
I / O
MATRIX PREVIEW
C O N T R O L
PRESET
ENTER
ESCVIEW
ESCVIEW
2 seconds
All Control buttons light with one flashing.
Both I/O buttons light with one flashing.
The flashing Control button indicates the baud rate
as follows:
Enter — 9600 Preset — 19200
View
<
— 38400 Esc
>
— 115200
Press and
hold the Enter, Preset,
Vie
w
<
, and Esc
>
buttons.
= Blinking button
The flashing I/O button indicates the protocol as follows:
Matrix — RS-232 Preview — RS-422/RS-485
In this example, the port is set to RS-232 at 9600 baud.
Figure 58. Enabling Serial Port Configuration Mode
2. Release the Control buttons.
3. To change a value, press and release the button that relates to the desired value.
Baud rate:
• Enter selects 9600 baud.
• Preset selects 19200.
• View
<
selects 38400 baud.
• Esc
>
selects 115200 baud.
Protocol:
• Matrix selects RS-232
• Preview selects RS-422.
C O N T R O L
PRESET
ENTER
I / O
MATRIX PREVIEW
ESCVIEW
= Blinking button
Press and release the button(s) to configure the port as
follows:
Baud rate:
Enter — 9600 Preset — 19200
View
<
— 38400 Esc
>
— 115200
Serial protocol:
Matrix — RS-232 Preview — RS-422/RS-485
The selected b
uttons blink and the others remain lit.
In this
example, the port is set to RS-422 at 38400 baud.
Figure 59. Selecting RS-232 or RS-422 and the Baud Rate
- User Guide 1
- HDXP Plus Series 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- Introduction 7
- Features 8
- Application Diagrams 11
- Installation 12
- Connections 13
- HDXP Plus 3232 14
- Reset Button 15
- Ethernet Connection 16
- RS-232 FunctionPin Function 17
- Operation 19
- HDXP PLUS SERIES 20
- Control Buttons 21
- I/O Buttons 22
- Operations 23
- MATRIX PREVIEW 24
- 17 18 19 20 21 22 23 24 25
- 1 2 3 4 5 6 7 8 25
- Breaking ties 27
- Previewing an Input 29
- I/O Grouping 32
- Creating I/O groups 33
- Saving and Recalling Presets 35
- Saving a preset 36
- Recalling a preset 37
- = Blinking Button 38
- Muting and Unmuting Outputs 39
- Unmuting an output 40
- Reset Modes Summary 44
- = Blink three times 45
- = blink four times 45
- Troubleshooting 46
- Configuration Worksheets 47
- Daily configuration 3 48
- System test 3 49
- HDXP Configuration Worksheet 50
- Configuration and 51
- Ethernet Port 52
- Host-to-Switcher Instructions 53
- Switcher-Initiated Messages 53
- Switcher Error Responses 54
- Symbol Definitions 55
- (Host to Switcher) 60
- (Switcher to Host) 60
- ASCII Command 67
- Response 67
- Additional Description 67
- IP Setup Commands (continued) 69
- Matrix Software 73
- Download link to the 74
- Using the Software 76
- Setting up the Matrix window 79
- Managing Ties 80
- IP Setup 81
- Setting the matrix IP address 82
- Setting the subnet mask 83
- Hardware Address field 83
- Enabling and disabling DHCP 83
- Setting the date 84
- Setting the local time 84
- Sync Time to PC button 84
- Setting the offset from GMT 84
- Setting the user password 85
- To: Charley Adams 86
- Updating the Firmware 87
- Uploading HTML Files 89
- Windows Menus 90
- Tools menu 91
- Preferences menu 93
- Using Emulation Mode 95
- Start menu group, select 97
- 2928 30 31 32 98
- Replacing Button Labels 100
- Blank Button Labels 101
- HTML Configuration 102
- Special Characters 103
- System Status Page 104
- System Settings Page 105
- IP Settings Fields 106
- Date/Time Settings Fields 107
- Passwords Page 108
- Email Settings Page 109
- Email address fields 110
- Firmware Upgrade Page 111
- Upload button 112
- Uploading... 112
- Upload. The 112
- Uploading Files 113
- Adding a Directory 114
- Set and View Ties Page 115
- Output Settings Page 116
- Global Presets Page 117
- Reference 118
- Information 118
- Setting an IP Address 119
- Subnet Mask 120
- Pinging for the IP Address 120
- Connecting as a Telnet Client 121
- Operating using Telnet 122
- Subnetting, a Primer 123
- Subnet masks and octets 124
- Contact Information 125
- Extron Warranty 125
Relacionado con productos y manuales para Accesorios para vídeo Extron-electronics HDXP Plus Series User Guide
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.145 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales