Extron-electronics HDXP Plus Series User Guide Manual de usuario Pagina 43
- Pagina / 125
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
HDXP Plus Series Switchers • Operation 37
4. Press and release an input or output button to exit the serial port configuration mode.
C O N T R O L
PRESET
ENTER
I / O
MATRIX PREVIEW
ESCVIEW
5
All Control and I/O buttons become unlit
or return to background illumination.
Press and release an
input or output b
utton.
Figure 60. Exiting Serial Port Configuration Mode
Resetting
There are several methods by which you can reset the HDXP, and some of these methods
allow for four levels of resetting. The following reset methods are available on the HDXP:
• Front panel buttons
• Rear panel reset button
• SIS commands
• Windows-based control software
The front panel and rear panel reset methods are discussed in this section. For information
about resetting via SIS commands, see the Remote Configuration and Control section
beginning on page 45. For information about using the Windows-based software to reset,
see the Matrix Software section beginning on page 67.
Resetting using front panel buttons
The front panel (system) reset is identical to the E ZXXX } SIS command, which returns
the HDXP to its factory-set defaults (see the Remote Configuration and Control
section). A system reset clears all ties, presets, and output muting, and resets all I/O
grouping.
To reset the switcher to the factory default settings, press and hold the Matrix and
Preview buttons while you apply AC power to the switcher.
NOTE: System reset does not reset the Internet protocol (IP) settings or replace
user-installed firmware.
Powe
r
I / O
MATRIX PREVIEW
Press and
hold
the Matrix and Preview buttons
while you apply power to the switcher.
The I/O b
uttons blink red, green, amber, then off.
Continue to hold the Matr
ix and Preview buttons until all input and
output b
uttons become unlit and the Matrix button lights green.
Release the Matrix and Preview buttons.
Figure 61. Resetting the System from the Front Panel
- User Guide 1
- HDXP Plus Series 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- Introduction 7
- Features 8
- Application Diagrams 11
- Installation 12
- Connections 13
- HDXP Plus 3232 14
- Reset Button 15
- Ethernet Connection 16
- RS-232 FunctionPin Function 17
- Operation 19
- HDXP PLUS SERIES 20
- Control Buttons 21
- I/O Buttons 22
- Operations 23
- MATRIX PREVIEW 24
- 17 18 19 20 21 22 23 24 25
- 1 2 3 4 5 6 7 8 25
- Breaking ties 27
- Previewing an Input 29
- I/O Grouping 32
- Creating I/O groups 33
- Saving and Recalling Presets 35
- Saving a preset 36
- Recalling a preset 37
- = Blinking Button 38
- Muting and Unmuting Outputs 39
- Unmuting an output 40
- Reset Modes Summary 44
- = Blink three times 45
- = blink four times 45
- Troubleshooting 46
- Configuration Worksheets 47
- Daily configuration 3 48
- System test 3 49
- HDXP Configuration Worksheet 50
- Configuration and 51
- Ethernet Port 52
- Host-to-Switcher Instructions 53
- Switcher-Initiated Messages 53
- Switcher Error Responses 54
- Symbol Definitions 55
- (Host to Switcher) 60
- (Switcher to Host) 60
- ASCII Command 67
- Response 67
- Additional Description 67
- IP Setup Commands (continued) 69
- Matrix Software 73
- Download link to the 74
- Using the Software 76
- Setting up the Matrix window 79
- Managing Ties 80
- IP Setup 81
- Setting the matrix IP address 82
- Setting the subnet mask 83
- Hardware Address field 83
- Enabling and disabling DHCP 83
- Setting the date 84
- Setting the local time 84
- Sync Time to PC button 84
- Setting the offset from GMT 84
- Setting the user password 85
- To: Charley Adams 86
- Updating the Firmware 87
- Uploading HTML Files 89
- Windows Menus 90
- Tools menu 91
- Preferences menu 93
- Using Emulation Mode 95
- Start menu group, select 97
- 2928 30 31 32 98
- Replacing Button Labels 100
- Blank Button Labels 101
- HTML Configuration 102
- Special Characters 103
- System Status Page 104
- System Settings Page 105
- IP Settings Fields 106
- Date/Time Settings Fields 107
- Passwords Page 108
- Email Settings Page 109
- Email address fields 110
- Firmware Upgrade Page 111
- Upload button 112
- Uploading... 112
- Upload. The 112
- Uploading Files 113
- Adding a Directory 114
- Set and View Ties Page 115
- Output Settings Page 116
- Global Presets Page 117
- Reference 118
- Information 118
- Setting an IP Address 119
- Subnet Mask 120
- Pinging for the IP Address 120
- Connecting as a Telnet Client 121
- Operating using Telnet 122
- Subnetting, a Primer 123
- Subnet masks and octets 124
- Contact Information 125
- Extron Warranty 125
Relacionado con productos y manuales para Accesorios para vídeo Extron-electronics HDXP Plus Series User Guide
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales