Extron-electronics SME 100 User Guide Manual de usuario Pagina 46
- Pagina / 185
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
About the Auto Image Submenu
NOTES:
• When the auto-image feature is enabled and a new input signal is detected, the
SME100 first attempts to apply values that were stored in auto memory to the input
signal (if the auto memory feature is enabled). If no auto memory exists, values that
are obtained from the auto-image feature are applied to the new input signal.
• If the auto-image feature is disabled and no auto memory picture information exists,
the SME100 uses default picture settings when an input signal is connected.
• See the "About the Auto Memory Submenu" section on page 38 for more
information on how the Auto Image and Auto Memory submenus affect each other.
• For information on enabling or disabling the auto-image feature using the web-based
user interface, see the "Encoder Settings Page" section on page 88.
• For information on enabling or disabling the auto-image feature using
SIS commands, see "Auto-image" on page 134 of the "Command and Response
Table for SIS Commands" section.
When an input is connected to the SME100 and the Auto Image submenu is set to On, an
automatic image adjustment is applied to the input signal. Auto-image measures where the
active areas start and stop and adjusts the input signal accordingly, so that the output image
fills the window. How the screen is filled is determined by the Aspect Ratio submenu
(see the "About the Aspect Ratio Submenu" section on page 41).
The table below details the settings that are affected when auto-image is turned on.
Auto Image Affected Settings
Primary Menu Affected Settings
Input Config
Horizontal Start Horizontal Active Pixels
Vertical Start Vertical Active Lines
Pixel Phase
Picture Control
Horizontal Position Horizontal Size
Vertical Position Vertical Size
NOTE: The remaining configuration options are left unchanged when auto-image is
enabled.
Auto-image is useful in applications where a variety of input sources are likely to be
encountered, such as on a lectern or podium where guest laptops might be connected.
SME100 • Front Panel Operation 40
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Relacionado con productos y manuales para Hardware Extron-electronics SME 100 User Guide
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales