Extron-electronics SME 100 User Guide Manual de usuario Pagina 81
- Pagina / 185
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Backing Up the SME100 Using Backup All
If a Backup All has never been done, or to do a routine backup of both the IP and Box
configuration files:
1. Connect the SME100 (see "Rear Panel Features" on page 12).
2. Open a web-browser and enter the IP address of the SME100 (see "Accessing the
Web-based User Interface" on page 47).
3. Go to the File Management Tab (see figure 68 on page 74).
4. Select the Backup/Restore link on the left sidebar of the File Management page.
5. Under Backup select Backup All (item
a
in figure 68 on page 74).
NOTE: Two files, IP.CFG and BOX.CFG are placed in the nortxe-backup directory.
Prior to the first backup, the nortxe-backup directory does not exist. The
SME100 creates it, then places the two files in it.
Backup of the current SME100 configuration is complete. The two files
(IP.CFG and BOX.CFG) can be used at any time to return the SME100 to this state.
At this time, copies of the two files (IP.CFG and BOX.CFG) should be saved to a remote
location for future use (see "Saving Files" on page72).
Restoring Config Files from the Backup
Once a Backup All has been completed, the two backup files exist in the SME100
nortxe-backup directory on the File Management page. To restore the IP.CFG or BOX.CFG
files after making undesired changes, or to return the SME100 to a known state:
1. Connect the SME100 (see "Rear Panel Features" on page 12).
2. Open a web browser and enter the IP address of the SME100 (see "Accessing the
Web-based User Interface" on page 47).
3. Select the File Management Tab (see figure 68 on page 74).
4. Select the Backup/Restore link on the left sidebar of the File Management page.
5. Under Restore there are two options to restore either the IP.CFG (
b
in figure 68 on
page 74) or BOX.CFG (
c
in figure 66). Select the config file to restore. The restore
program starts automatically.
6. Once completed, the program redirects to the Live View page.
NOTE: When restoring both configuration files, always do the BOX.CFG first
followed by the IP.CFG. That prevents having to change the IP settings until
after both configuration files have been restored.
Restoring the Configuration from Another SME100
A BOX.CFG file from another SME100 can be used to restore your SME100 to a known
configuration using the following instructions.
NOTES:
• Only use a donor SME100 with the same firmware version.
• In the following procedures, the donor SME100 is referred to as device D; the
SME100 that will be restored with the donor configuration is referred to as
device A.
SME100 • Web-based User Interface Operation 75
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Relacionado con productos y manuales para Hardware Extron-electronics SME 100 User Guide
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales